The Compliance Pack: What Procurement Needs Before It Can Approve A Liner
By Kwickway Products · November 6, 2026 · 5 min read

Most suppliers lose vendor approvals in the same place: a QA reviewer asks for documentation, the supplier sends marketing copy, and the file sits open until someone gives up.
This is what a hotel group, contract caterer or healthcare foodservice operator actually asks for on a tabletop liner, what each document means, and where the common misunderstandings are.
There is no FDA certificate. That is not a gap.
The most frequent request is for an "FDA certificate" or an approval number. No such document exists for any food-contact article, from any supplier.
The FDA regulates food-contact materials, not finished articles, and it does not certify or approve them. A material either complies with the applicable regulation or it doesn't. Any supplier who sends you a certificate number for a tray liner is sending you something they made up.
What exists, and what you should ask for instead:
The applicable regulation. For SlipSafe liners that is 21 CFR 177.1640, which covers polystyrene and rubber-modified polystyrene. It sits in Part 177, Indirect Food Additives: Polymers, Subpart B, governing substances used as basic components of single and repeated use food-contact surfaces.
A supplier declaration of compliance. A written statement from the manufacturer that the material complies with that regulation, on letterhead, signed and dated.
That pair is what a competent reviewer wants. The certificate request usually comes from a template rather than from the reviewer's own understanding, and naming the regulation tends to resolve it in one email.
The documents worth requesting
Material identification. The polymer named specifically. "Food-safe plastic" tells you nothing. SlipSafe liners are thin film foamed polystyrene.
Declaration of compliance. As above, referencing 21 CFR 177.1640.
Intended use statement. How the article is meant to be used. These liners go beneath plates, glassware, ramekins and cups rather than in direct contact with food, which is why they fall under indirect food additives.
Maximum service temperature. Ours is 158°F (70°C). This one matters more than most buyers expect, and the next section explains why.
Material composition and recycled content. Up to 80% post-industrial recycled content. Ask any supplier for the figure and the pre- versus post-consumer split rather than accepting "made with recycled materials".
Manufacturing location. Die-cut in Toronto, Ontario, and manufactured in a solar-powered facility. Relevant to lead time, supply resilience and increasingly to ESG screens.
Single-use confirmation. Stated explicitly. It determines whether your hygiene protocol needs a cleaning and sanitation procedure for the item at all. For SlipSafe liners it does not, because each liner serves one service and is discarded.
The temperature question is the one that catches people
Ask every tabletop supplier for a number, and treat "resists high heat" as a non-answer. The food safety position on these liners covers the contact question in more depth.
Foamed polystyrene softens around 70–80°C. We publish 158°F (70°C) as the maximum service temperature, which means liners should not sit in direct contact with hot plates, under heat lamps, or inside heated holding cabinets and trolleys.
In practice that constraint is easy to work within, because the plate, cup or glass sits between the heat source and the liner. A covered main on a banquet tray, a coffee cup on a coaster, a ramekin on a liner, all well inside range.
But if a supplier tells you their film liner handles high heat, ask for the figure. Coffee is served hotter than 158°F. The claim is almost always wrong, and the operator who believes it is the one who finds out.
Building the vendor file
A complete submission usually contains:
| Document | What it establishes |
|---|---|
| Material identification | What the product actually is |
| Declaration of compliance | Regulatory position, citing 21 CFR 177.1640 |
| Intended use statement | Indirect contact, beneath service ware |
| Maximum service temperature | 158°F (70°C) operating boundary |
| Composition and recycled content | ESG and procurement screens |
| Manufacturing location | Supply chain and lead time |
| Single-use confirmation | Whether a sanitation procedure is required |
Request the set in one email rather than one document at a time. A supplier who can produce all seven quickly is a supplier who has done this before.
What we can send
We can provide the above on request, and we'd rather you ask for it early in an evaluation than discover a gap at the approval stage.
Contact our team for documentation, or request free samples to run alongside the paperwork. Full specifications are on the brand standards and RFP guide.
US orders ship from Toronto and our Buffalo, NY hub, with regional distribution through New York, Chicago, Miami, Las Vegas and Los Angeles.
FAQ
Is there an FDA certificate for non-slip tray liners? No. The FDA does not certify or approve food-contact articles, so no certificate number exists for any product in this category. What exists is compliance with the applicable regulation. For these liners, 21 CFR 177.1640, and a supplier declaration of compliance.
What regulation covers polystyrene food-contact materials? 21 CFR 177.1640, covering polystyrene and rubber-modified polystyrene, within Part 177, Indirect Food Additives: Polymers.
What is the maximum service temperature? 158°F (70°C). Liners should not be placed in direct contact with hot plates, under heat lamps, or in heated holding equipment. In normal service the plate, cup or glass sits between the heat source and the liner.
Are the liners direct or indirect food contact? They are used beneath plates, glassware, ramekins and cups rather than in direct contact with food, which places them under indirect food additives.
What recycled content do they contain? Up to 80% post-industrial recycled material.
What documents should an RFP request from a liner supplier? Material identification, a declaration of compliance citing the applicable regulation, an intended use statement, maximum service temperature, composition and recycled content, manufacturing location, and written confirmation of single-use.
